注塑级聚四氟乙烯 日本大金 注塑级PTFE  PTFE  Polymist® XPP 538塑料是东莞市双帮塑胶原料有限公司常年销售的塑料,因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告,COA原料出厂报告,UL黄卡,ROSH报告,reach报告,SVHC报告,提供原料注塑加工工程中可能出现的各种异常现象解决方法,塑料牌号太多,本网站没有提供的本公司也有代理,详情请咨询本公司相关业务人员0769-87795123

 
13549213581  肖生
 
粉状
Polymist® XPP 538
聚四氟乙烯
Solvay Specialty Polymers
Technical Data
产品说明
Polymist® XPP 538是一种聚四氟乙烯 (PTFE)材料,。 该产品在北美洲、欧洲或亚太地区有供货,。
Polymist® XPP 538的典型应用领域为:添加剂/色母粒
总体
材料状态 • 已商用:当前有效
资料 1 •  Technical Datasheet
搜索 UL 黄卡 •  Solvay Specialty Polymers
供货地区 • 北美洲 • 欧洲 • 亚太地区
用途 • Additive
外观 • 白色
形式 • 粉状
 
物理性能 额定值单位制 测试方法
Bulk Density 400g/l ASTM D4895
比表面积 3.0m²/g 内部方法
颗粒大小 - (D50/D99) 4.50 到 15.0µm 内部方法
补充信息 额定值单位制 测试方法
Grind in Oil - NPIRI 2.50 NPIRI
Melt Temperature 320 到 330°C ASTM D3418
Processing
 
• Polymist® XPP 538 is used as additives in paints and coatings where improvements in non-stick, mar resistance, slip, chemical resistance, and moisture repelling characteristics are desired.
 
• Polymist® XPP 538 may be used independently as an additive or in combination with polyethylene waxes. The PTFE content at the surface layer is required in order to impart the properties of PTFE to the coating, substantially. Extreme environmental demands on greases, such as those experienced in the automotive industry (i.e. wide temperature ranges and heavy loads) can be accommodated by the addition of Polymist® XPP 538 micronized powders.
 
• Polymist® XPP 538 can be dispersed easily at room temperature, and it doesn't agglomerate at temperatures used during formulation or printing. Chemical inertness and improved temperature resistance give ink formulators the opportunity to use a variety of solvents without adverse chemical reactions.
 
• Elastomeric parts containing Polymist XPP® 538 will exhibit improved lubricity, increased (hot) tear strength, better flex life and reduced friction and wear. In addition XPP 538 can be used at low concentrations to improve mold release properties. Internal or open mixers (e.g. Banbury or two-roll mixers) are normally used to allow a good distribution of Polymist® XPP 538 in the elastomeric compound. Additional fillers are normally included with Polymist® XPP 538 during the blending process. The resulting elastomeric composition can then be processed under normal conditions.
 
Storage and Handling
• The usual precautions for safe storage and handling of Polymist® XPP 538 should be taken according to material safety documentation and experience. There will be no chemical deterioration of the Polymist® XPP 538 during proper storage.
 
• Shelf life of Polymist® XPP 538 micronized powders will vary depending upon whether the recommended storage conditions are maintained and whether the material remains free from foreign contamination during storage time (not exposed to dirt, dust, water or other chemicals). The material should remain sealed in the original containers and storage conditions should provide for protection from temperature extremes as well as rain, snow or other wet environments (or such conditions which may damage the storage containers in which the product is stored).
 
Safety and Toxicology
• Before using PTFE Polymist® XPP 538 micronized powders consult the product Material Safety Data Sheet and follow all label directions and handling precautions.
 
• As with all PTFE materials, handling and processing should only be carried out in well ventilated areas. Vapor extractor units should be installed above processing equipment. Fumes must not be inhaled and eye and skin contact ought to be avoided. In case of skin contact wash with soap and water. In case of eye contact flush with water immediately and seek medical help. Do not smoke in areas contaminated with powder, vapor or fumes. See Material Safety Data Sheet for detailed advice on waste disposal methods.
 
Packaging
• Polymist® XPP 538 is packaged in 25 kg non returnable drums. Each drum has one bag liner made of polyethylene resin.
 
 
 
注塑级聚四氟乙烯 日本大金 注塑级PTFE   PTFE  Polymist® XPP 538塑料是东莞市双帮塑胶原料有限公司常年销售的塑料,因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告,COA原料出厂报告,UL黄卡,ROSH报告,reach报告,SVHC报告,提供原料注塑加工工程中可能出现的各种异常现象解决方法,塑料牌号太多,本网站没有提供的本公司也有代理,详情请咨询本公司相关业务人员0769-87795123
 
13549213581  肖生