注塑级PTFE 美国3M PTFE Dyneon™ TF 2053 Z PTFE

 
塑料是东莞市双帮塑胶原料有限公司常年销售的塑料,因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告,COA原料出厂报告,UL黄卡,ROSH报告,reach报告,SVHC报告,提供原料注塑加工工程中可能出现的各种异常现象解决方法,塑料牌号太多,本网站没有提供的本公司也有代理,详情请咨询本公司相关业务人员0769-87795123
 
13549213581
Technical Information
 
 
 
 
 
 
 
 
 
 
 
Dyneon™
TF 2053 Z PTFE
 
PTFE Fine Powder for Tubing
 
 
 
 
Dyneon™ TF 2053 Z PTFE is an ideal grade for extrusion of tubing and cables requiring only moderately high reduction ratio.
 
Product Features:
• Processable by standard paste • Emulsion Polymerization PTFE
extrusion methods • Meets ASTM D4895-04 Type 1, Grade 1,
• Good overall balance of mechanical Class C classification
properties and processability
Typical Properties (Not for specification purposes)
Property Test Method Unit Value
Powder Properties
Average particle size ISO 13320 µm 520
Bulk density ISO 12086 kg/m3 500
Processing
Range of Reduction Ratios (RR) Dyneon Method 20:1 to 1200:1
Extrusion pressure ASTM D4895 MPa 65
 
Mechanical Properties (measured on sintered sheets according to ISO 12086)
 
Tensile strength DIN EN ISO 527-3 MPa 32
Elongation at break DIN EN ISO 527-3 % 390
Specific Gravity DIN EN ISO 12086 g/cm3 2.16
 
 
Product Form and Packaging
Dyneon™ TF 2053 Z PTFE is supplied in moisture and dust-tight plastic drums. Capacity per drum: 25 kg. Order quantity per pallet: 300 kg.
 
TF 2053 Z PTFE
 
 
 
 
 
 
 
 
 
 
Our Worldwide Commitment to Quality
 
Indicative of our commitment, most Dyneon design, development, production and service facilities have achieved global quality management certification. Production facilities have also received certification for their environmental management system. Please see the Dyneon website (www.dyneon.com) for the most up-to-date certification details.
 
Storage and Material Handling
 
Dyneon TF 2053 Z PTFE can be stored for 3 years from the date of manufacture provided it is stored in a clean, dry place in the original, unopened container received from Dyneon at a temperature of less than 19°C. Before processing, it is advisable to store the material in a sealed container for at least 24 hours in the production area to eliminate the risk of condensation in the powder. This is particularly important when ambient temperature is low, in such cases the material should be conditioned for up to 72 hours in the production area.
 
Safety/Toxicology
This is a PTFE material, so normal precautions observed with PTFE should be followed. Before processing this product, be sure to read and follow all precautions and directions for use contained in the product label and the Material Safety Data Sheet. General handling/processing precautions include: (1) Process only in well-ventilated areas; (2) Do not smoke in areas contaminated with powder/residue from this product; (3) Avoid eye contact; (4) After handling this product wash any contacted skin with soap and water; (5) Avoid contact with hot fluoropolymer. Potential hazards, including evolution of toxic vapors, can exist if processing occurs under excessively high temperature conditions. Appropriate local exhaust ventilation
 
such as vapor extractor units should be installed above processing equipment. When cleaning processing equipment, do not burn off this product with an open flame or in a furnace.
 
Technical Information: Technical information and data, recommendations, and other statements provided by Dyneon are based on information, tests, or experience which Dyneon believes to be reliable, but the accuracy or completeness of such information is not guaranteed. Such technical information and data are intended for persons with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any Dyneon or third party intellectual property rights is granted or implied with this information.
 
 
 
 
 
 
 
 
 
 
Important Notice:
 
Because conditions of product use are outside Dyneon’s control and vary widely, user must evaluate and determine whether a Dyneon product will be suitable for user’s intended application before using it. The following is made in lieu of all express and implied warranties (including warranties of merchantability and fitness for a particular purpose): If a Dyneon product is proved to be defective, Dyneon‘s only obligation, and user’s only remedy, will be, at Dyneon‘s option, to replace the quantity of product shown to be defective when user received it or to refund user’s purchase price. In no event will Dyneon be liable for any direct,
 
indirect, special, incidental, or consequential loss or damage, regardless of legal theory, such as breach of warranty or contract, negligence, or strict liability.
 
Product Stewardship - Replacement Emulsi-fier. Dyneon fluoroplastic products identified with a “Z” following the product name indicate products that are made using Dyneon’s new re-placement emulsifier. The new emulsifier is a polymerization aid used to manufacture certain fluoropolymers and is not an intended ingredient in the polymers. The new emulsifier eliminates the use of the former polymerization aid, APFO (ammonium perfluorooctanoate, the ammonium salt of perfluorooctanoic acid (PFOA)), in the manufacture of these fluoropolymers. The use of the replacement emulsifier in the manufac-ture of these Dyneon products is consistent with Dyneon’s product stewardship principles and our commitment to US EPA’s Voluntary PFOA Stewardship Program under which fluoropo-lymer manufacturers agreed to work towards eliminating PFOA in emissions and product content by the year 2015. Dyneon is pleased to report that we will have completely eliminated the use of APFO in our manufacturing processes by the end of December 2008.
 
 
 
© Dyneon 2009
Issued 8/09
 
 
 
 
 
 
 
 
 
东莞市双帮塑胶原料有限公司大量销售塑料注塑级PTFE 美国3M PTFE Dyneon™ TF 2053 Z PTFE
 
 
 
 
因为塑料价格行情每天都有新的变化前天的报价不等于今天的报价。如果需要新的价格请电:13549213581,肖生。