塑料是东莞市双帮塑胶原料有限公司常年销售的塑料，因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告，COA原料出厂报告,UL黄卡,ROSH报告,reach报告,SVHC报告,提供原料注塑加工工程中可能出现的各种异常现象解决方法，塑料牌号太多，本网站没有提供的本公司也有代理，详情请咨询本公司相关业务人员0769-87795123

 

13549213581

Technical Information

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Dyneon™

 

Modified granular PTFE for compression molding

 

TFM™ 1705 PTFE

 

 

Features and Typical properties (Data not for specification purposes)

 

Benefits

 

 

Powder properties

 

 

• Meets ASTM D 4894 Type III, Grade 1 resin 

 

• Non-free-flowing compression molding powder 

 

• Very fine particle size 

 

• Improved gel stability 

 

• Denser polymer structure, low permeation 

 

• Excellent flex life 

 

• Improved weldability 

 

• Lower deformation under load 

 

• Very good electrical and mechanical properties 

 

• Increased modulus of elasticity 

 

• Excellent for tall, thick-walled billets 

 

 

 

Property Value Unit Test Method

Bulk density 420 g/l ASTM D 4894-98a

Average particle size 25 µ ASTM D 4894-98a

 

Mechanical properties, measured at 23ºC (73ºF) on sintered moldings

 

Property Value Unit Test Method

Tensile Strength 4800 psi ASTM D 4894-98a

Elongation at break 450 % ASTM D 4894-98a

Specific gravity 2.16 g/cc ASTM D 4894-98a

Shrinkage 5.8 % ASTM D 4894-98a

Tensile Modulus 94,250 psi ASTM D 638

Deformation under Load % ASTM D 621

2175 psi – 24 hr 9

2175 psi – 100 hr 10

2175 psi – permanent 4.5

Thermal properties

Property Value Unit Test Method

Flammability V-0 UL94

Melt point (initial) 342 ± 10 ºC ASTM D 4894-98a

(second) 327 ± 10 ºC ASTM D 4894-98a

Service Temperature Range -200ºC to 260ºC

(-328ºF to 500ºF)

Electrical Properties

Property Value Unit Test Method

Dielectric Strength 3.7 kV/mil ASTM D149-95a

 

Dyneon™ TFM™ 1705 PTFE

 

 

 

 

 

 

 

 

 

 

 

 

 

Processing Information

 

If transport or storage temperatures are too high the material can agglomerate in its container. In such cases, it is advisable to store the material for 48 hours at below 23ºC (73ºF) and then sieve it (mesh size 4 mm) (.16 in) before filling the mold. To achieve optimum properties, compression molding should be carried out within a temperature range of 23ºC to 26ºC (73ºF to 78ºF) at a pressure of

20-25 MPa (2900-5100 psi). The sintering temperature should be in the range of 375ºC to 380ºC (707ºF to 716ºF).

 

Product Form and Packaging

 

Dyneon TFM 1705 PTFE is supplied in moisture and dust-tight plastic drums with a polyethylene liner.

Quantity per drum: 25 kg (55 lbs.)

 

Order quantity per pallet: 150 kg (330 lbs.)

 

Storage and Material Handling

 

Dyneon TFM 1705 PTFE has an unlimited shelf life provided it is stored in a clean, dry place. Dyneon TFM 1705 PTFE is hydrophobic, and generally do not require drying before processing unless high humidity conditions create surface moisture adsorption.

 

Management System - ISO 9001 and ISO 14001

 

All Dyneon design, development, production and service facilities have achieved a global ISO 9001 registration for their quality management system. In addition, our Gendorf, Germany location has achieved ISO 14001 for its environmental management system.

 

Regulatory

 

Dyneon TFM 1705 PTFE is in compliance with FDA regulation 21 CFR 177.1550. It is the responsibility of the user to determine whether its specific formulation and intended use comply with applicable laws and are suitable for its intended applications.

 

Safety/Toxicology

 

These are fluoroplastic materials, so normal precautions observed with fluoroplastics should be followed. Before processing these products, consult the Material Safety Data Sheet and follow all label directions and handling precautions. General handling/processing precautions include: (1) Process only in well-ventilated areas;

(2) Do not smoke in areas contaminated with powder/residue from these products; 

 

(3) Avoid eye contact; (4) After handling these products wash any contacted skin with soap and water. Potential hazards, including evolution of toxic vapors, can exist if processing occurs under excessively high temperature conditions. Vapor extractor units should be installed above processing equipment. When cleaning processing equipment, do not burn off any of this product with an open flame or in a furnace. 

 

Technical Information and Test Data

 

Technical information, test data, and advice provided by Dyneon personnel are based on information and tests we believe are reliable and are intended for persons with knowledge and technical skill sufficient to analyze tests types and conditions, and to handle and use raw polymers and related compounding ingredients. No license under any Dyneon or third party intellectual rights is granted or implied by virtue of this information.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Important Notice:

Because conditions of product use are out-side Dyneon’s control and vary widely, user must evaluate and determine whether a Dyneon product will be suitable for user’s intended application before using it. The following is made in lieu of all express and implied warranties (including war-ranties of merchantability and fitness for a particular purpose): If a Dyneon prod-uct is proved to be defective, Dyneon‘s only obligation, and user’s only remedy, will be, at Dyneon‘s option, to replace the quantity of product shown to be defec-tive when user received it or to refund user’s purchase price. In no event will Dyneon be liable for any direct, indirect, special, incidental, or consequential loss or damage, regardless of legal theory, such as breach of warranty or contract, negligence, or strict liability.

 

 

 

 

 

东莞市双帮塑胶原料有限公司大量销售塑料注塑级PTFE 美国3M PTFE Dyneon™ TFM™ 1705 PTFE

 

 

 

 

因为塑料价格行情每天都有新的变化前天的报价不等于今天的报价。如果需要新的价格请电：13549213581，肖生。