可溶性聚四氟乙烯 日本大金 PFA AP-201

 
塑料是东莞市双帮塑胶原料有限公司常年销售的塑料,因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告,COA原料出厂报告,UL黄卡,ROSH报告,reach报告,SVHC报告,提供原料注塑加工工程中可能出现的各种异常现象解决方法,塑料牌号太多,本网站没有提供的本公司也有代理,详情请咨询本公司相关业务人员0769-87795123
 
13549213581
Pr oduc t i  nf o r m a t io n
 
DAIKIN-NEOFLON ®PFA
 
 
Daikin PFA is a copolymer of tetrafluoroethylene (TFE) and perfluoroalkyl vinyl ether. DAIKIN-Neoflon® PFA has the molecular structure shown below. Melting points range from 295 to 310 ̊C.Compared to FEP, the copolymerization composition ratio of the comonomer content
is small, and PFA has a chemical structure that is close to PTFE. Therefore, PFA has a higher melting point and higher heat resistance than FEP. Daikin PFA has excellent mechanical strength at high temperatures, and has excellent moldability for easy processing using extrusion, compression, blow, transfer, and injection molding methods.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Thermal Properties: Due to the high bonding strength of the carbon, fluorine, and oxygen atoms, PFA demonstrates̊̊ nearlẙ the same̊ outstanding capabilities as PTFE in temperat ures ranging from -200 C to 260 C. From 200 C to 260 C, PFA maintains its flexibilitẙ̊ without a loss of toughness. The maximum continuous use temperature use for PFA is 260 C (500 F). This is the highest temperature for continuous use of any fluoropolymer resin.
 
Chemical Properties: Daikin PFA provides excellent chemical resistance.
 
Electrical Properties: A low dielectric constant and dissipation factor exist along with high dielectric strength over a wide range of frequencies and temperatures.
 
 
Low Friction: Daikin PFA is inherently non-cohesive and it is extremely repellant of water, oil and other substances. Furthermore, its surface is characterist ically slippery.
 
 
 
 
 
Daikin America, Inc. 20 Olympic Drive, Orangeburg, New York (845) 365-9500 (800) 365-9570 Fax: (845) 365-9515 Web: www.daikin-america.com
 
DAIKIN-NEOFLON ® PFA
 
Pellets Daikin PFA pellets have good melt flow characteristics and can be processed in the same manner
as other thermoplastic resins. The semiconductor grades (SH Series) have reduced elusion ions, and are
used for various components for semiconductor manufacture lines where cleanliness is essential.
Property Test AP-201 AP-202 AP-210 AP-220 AP-230 AP-201SH AP-211SH AP-221SH AP-231SH
Method
Bulk Density(g/l) 1200 1200 1200 1200 1200 1200 1200 1200 1200
Specific Gravity ASTM 2.14-2.15 2.14-2.15 2.14-2.15 2.14-2.15 2.14-2.15 2.14-2.15 2.14-2.15 2.14-2.15 2.14-2.15
D3307
MeltFlow Rate ASTM 20.0-30.0 63.0-81.0 10.0-17.0 3.0-9.0 1.5-2.5 20.0-30.0 10.0-30.0 35.1-9.9 1.5-5.0
(g/10min) D3307
Melting Point °C ASTM 300-310 300-310 300-310 300-310 300-310 300-310 300-310 300-310 300-310
D3307
ContinuousService 260 260 260 260 260 260 260 260 260
Temperature(°C)
Mechanical
Tensile Strength ASTM 20 20 25 25 30 20 25 25 30
(MPa),min D3307
Elongation ASTM 300 230 300 300 300 300 300 300 300
(%), min D3307
Compressive ASTM 5-6 5-6 5-6 5-6 5-6 5-6 5-6 5-6 5-6
Strength (MPa) D695
1 %
Deformation,
25°C
MIT Flex, cycles ASTM 11,000 5,300 20,000 100,000 600,000 11,000 60,000 200,000 1,800,000
D2176
Electrical
Dielectric ASTM 500-600 500-600 500-600 500-600 500-600 500-600 500-600 500-600 500-600
Breakdown D149
Strength (V/mil) Short time 1/8 in
Volume Resistivity ASTM 1018 1018 1018 1018 1018 1018 1018 1018 1018
(Ohm-cm) D257
Dielectric Constant ASTM D150
103 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1
106 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1
Dielectric ASTM D150
Dissipation 103 1x10-5 1x10-5 1x10-5 1x10-5 1x10-5 1x10-5 1x10-5 1x10-5 1x10-5
Factor 106 3x10-4 3x10-4 3x10-4 3x10-4 3x10-4 3x10-4 3x10-4 3x10-4 3x10-4
Combustibility ASTM >95 >95 >95 >95 >95 >95 >95 >95 >95
(%) D2863/Oxygen ConcentrationIndex 
 
Process Extrusion Extrusion Extrusion Extrusion Extrusion Injection Extrusion Extrusion Extrusion
Methods Injection Injection Injection Injection Injection
Uses Complicated Good Injection Tubing Linings, Goodfluidity, Tubingand Linings, Linings,
injection insulation molded and tubing suited to injection tubing tubing
molded parts for parts, wire making molded
requiring micro wire wire coating moldings of parts
high melt applica- insulation complex shapes requiring
flow to fill, tions requiring high stress
thin wall wire highfluidity crack
insulations resistance,etc.
 
 
Daikin America, Inc. 20 Olympic Drive, Orangeburg, New York (845) 365-9500 (800) 365-9570 Fax: (845) 365-9515 Web: www.daikin-america.com
 
DAIKIN-NEOFLON ®PFA
 
 
 
 
 
Polymer Processing of Daikin
 
PFA Pellets
 
Molding
 
PFA can generate traces of highly corrosive gas when it decomposes at the molding temperature, requiring materials of construction with outstanding corrosion and heat resistance for extrusion and injection-molding equipment used for molding.
 
 
Extrusion molding
 
In extrusion, covered electrical wire, pipe, tubing, monofilament, film, etc. can be formed by extrusion. Extruders with a cylinder diameter from 30 to 65 mm are most commonly used. A rapid compression type screw with an L/D ratio of 20 to 24 and compression ratio of 2.5 to 3.0 is also used.
 
 
Injection molding
 
DAIKIN PFA has good injection moldability and can easily mold complicated profiles, such as semiconductor manufacturing jigs, electrical and electronic components. A screw-type molding machine is generally used, and the spool, runner, and gate must be made slightly thicker than normal, as
 
short as possible, and have the cross section nearly circular to reduce molding strain. Hard chromium-plated dies are generally used.
 
 
Transfer molding
 
Pipe, valves, joints, and other linings for the chemical industry, brewing industry, etc. can be formed by transfer molding PFA. Components subject to lining processi ng, such as pipes and valves,
 
are used for the outer die or inner die, and are heated to temperatures that exceed the melting point. PFA resin that has been separately melted inside the cylinder is pressu re-fed into the components̊ and cooled while under pressure. Components̊ can be molded at die temperatures of 350 to 370 C and resin temperatures of 350 to 390 C.
 
 
Dispersions Neoflon PFA dispersions are water-based coatings with bases of co-polymers of tetrafluoroethylene
and perfluoroalkylvinylether.
Product No. Color Viscosity pH Solids Content Uses
(Cp) (%)
AD-2CRER White, 140-260 8-10 50 Dispersion makes pinhole free
milky films with non-stick properties
AW-5000R White, 15-65 7.5-11 47 Films with excellent abrasion
milky resistance and non-stick
properties. Used in printers and
copy rolls
 
 
 
 
 
 
 
 
 
 
 
 
Daikin America, Inc. 20 Olympic Drive, Orangeburg, New York (845) 365-9500 (800) 365-9570 Fax: (845) 365-9515 Web: www.daikin-america.com
 
DAIKIN-NEOFLON ®PFA
 
 
 
Coating Powders
 
 
Product No. Color Bulk Density Description Processing Methods
AC-5600 White 500 Up to a thickness of 100 µm Electrostatic spray coating
per single coat Fluidized bed coating
AC-5539 Gray 500 Multiple coats, up to 10,000 µm Roto molding, Roto lining
AC-5820 White 830 0.5-5.0mm thickness
AC-5830 Gray 850 0.5-5.0mm thickness Roto lining
ACX-31 White 750 30-80 µm thickness Electrostatic spray coating
ACX-34 White 700 30-80 µm thickness Electrostatic spray coating
 
 
Quality/Regulatory: Daikin PFA pellets comply with the requirements set forth in FDA specification 21 CFR.177.1550
 
Daikin America’s manufacturing facility is registered to ISO-9001 (Quality System), ISO-14001
 
(Environmental System) and Responsible Care 14001 (Safety, Health, Environment and Security).
 
 
Safety: When PFA resins are heated to temperatures above 300 ̊C, some decomposi tion products
may be given off.  These decomposition produc ts may be harmful , and inhalati on of
 
these fumes must be avoided. Ovens, process equipment and working area must be adequately
 
ventilated. For further information, please refer to the material safety data sheet for these
 
products and the Guide to the Safe Handling of Fluoropolymer Resins published by
 
SPI Inc., The Society of Plastics Industry, Inc., 1801 K Street, NW, Suite 600K, Washington,
 
DC, 20006-1301 (202-972-5200).
 
 
Medical Use: These products are not specifically designed or manufactured for use in implantable medical
and/or dental devices. They have not been tested for such applications and will only be
 
sold for such use pursuant to contract containing specific terms and conditions required by us.
 
 
 
 
 
 
 
 
 
 
All statements, information and data given herein are believed to be accurate and reliable, but are presented without guarantee, warranty or responsibility of any kind, expressed or implied. Statements or suggestions concerning possible use of our products are made without representation or warranty that any such use is free of patent infringement, and are not recommendations to infringe any patent. The user should not assume that all safety measures are indicated, or that other measures may not be required.
 
 
 
2.14.250
 
 
 
 
 
 
东莞市双帮塑胶原料有限公司大量销售塑料可溶性聚四氟乙烯  日本大金  PFA AP-201
 
因为塑料价格行情每天都有新的变化前天的报价不等于今天的报价。如果需要新的价格请电:13549213581,肖生。                      
 
 
 
 
 
 
 
 
 
 
 
 
因为塑料价格行情每天都有新的变化前天的报价不等于今天的报价。如果需要新的价格请电:13549213581,肖生。