PFA 美国3M PFA 3M™ Dyneon™ Fluoroplastic Powder PFA 6503PBZ塑料是东莞市双帮塑胶原料有限公司常年销售的塑料,因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告,COA原料出厂报告,UL黄卡,ROSH报告,reach报告,SVHC报告,提供原料注塑加工工程中可能出现的各种异常现象解决方法,塑料牌号太多,本网站没有提供的本公司也有代理,详情请咨询本公司相关业务人员0769-87795123

 
13549213581
Technical Data
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Features and Benefits
 
Excellent thermal stability 
 
Excellent electrostatics 
 
Excellent non-stick performance 
 
Outstanding flow and fluidization 
 
Excellent stress crack resistance 
 
Smooth surfaces 
 
Process targets: powder coating 
 
Non-wetting 
 
Heat resistant to 260°C (500°F) 
 
Low friction 
 
Good transparency 
 
Chemical resistant 
 
 
 
 
 
 
 
 
Note: Data in this document are not for specification purposes.
 
 
 
 
 
3M™ Dyneon™
 
Fluoroplastic Powder PFA 6503PBZ
 
Typical Properties
 
Property Test Method
Melting Point ASTM D4591
Melt Flow Index (372°C/5 kg) ASTM D1238
Specific Gravity ASTM D792
Bulk Density DIN 53466
Tensile Strength @ 23°C ASTM D638
Ultimate Elongation @ 23°C ASTM D638
Hardness Shore D ASTM D2240
LOI ASTM D2863
Flexural Modulus ASTM D790
Median Particle Size
 
 
Product Description
 
3M™ Dyneon™ Fluoroplastic Powder PFA 6503PBZ is a fluorothermoplastic powder with excellent thermal stability characteristics, designed for use in thin film powder coatings. Typical applications include non-stick surfaces, chemical vessel and tank liners, electrical insulation and low friction applications.
 
Product Form and Packaging
 
Dyneon PFA 6503PBZ is supplied in powder form. Product is supplied in 50kg (110 lb.) quantities.
 
Storage and Material Handling
 
PFA 6503PBZ has an extended shelf life provided it is stored in a clean, dry place in its original, unopened
 
container. PFA 6503PBZ is hydrophobic, and generally does not require drying before processing unless high humidity conditions create surface moisture adsorption. Opened containers should be tightly resealed to prevent dust contamination from static charge accumulation and moisture ingress. Containers should be equilibrated to room temperature before opening. Best performance is achieved by sieving with a 60 mesh sieve prior to use.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
308°C (586°F) 3 g/10 min 2.15 g/cc 800
 
30 MPa (4350 psi)
 
380%
 
60
 
>95
 
550 MPa (80,000 psi) 30µ
 
Safety/Toxicology
 
This is a fluoroplastic material, so normal precautions observed with fluoroplastics should be followed. Before processing this product, be sure to read and follow all precautions and directions for use contained in the product label and the Material Safety Data Sheet. General handling/processing precautions include: (1) Process only in well-ventilated areas; (2) Do not smoke in areas contaminated with powder/residue from this product;
 
(3) Avoid eye contact; (4) After handling this product wash any contacted skin with soap and water. Potential hazards, including evolution of toxic vapors, can exist if processing occurs under excessively high temperature conditions. Appropriate local exhaust ventilation such as vapor extractor units should be installed above processing equipment. When cleaning processing equipment, do not burn off this product with an open flame or in a furnace.
 
 
 
 
 
 
 
 
 
 
 
 
3
 
3M™ Dyneon™ Fluoroplastic Powder PFA 6503PBZ
 
 
 
 
 
 
 
 
 
Food Contact/FDA Regulatory Status
 
This 3M product complies with 21 CFR 177.1550 (perfluorocarbon resins under paragraph (a)(2)) and may be used as coatings or component of a coating for articles intended for repeated food contact, subject to the provisions, including specifications, conditions of use, and limitations, if any, in this regulation.
 
3M makes no recommendation about the suitability of this 3M product in the user’s intended application. It is the user’s responsibility to determine whether its use of a 3M product in a particular application is suitable and will comply with applicable laws and regulations. As appropriate, the user is also responsible for testing its finished product(s) made with 3M products to ensure compliance with any applicable specifications, conditions of use, and limitations (including extractives limitations) under applicable laws and regulations such as 21. C.F.R. 177.1550.
 
 
 
 
 
东莞市双帮塑胶原料有限公司大量销售塑料美国3M PFA 3M™ Dyneon™ Fluoroplastic Powder PFA 6503PBZ
 
 
 
 
因为塑料价格行情每天都有新的变化前天的报价不等于今天的报价。如果需要新的价格请电:13549213581,肖生。