ETFE 美国3M 3M™ Dyneon™

Fluoroplastic Granules
ET 6235Z
塑料是东莞市双帮塑胶原料有限公司常年销售的塑料,因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告,COA原料出厂报告,UL黄卡,ROSH报告,reach报告,SVHC报告,提供原料注塑加工工程中可能出现的各种异常现象解决方法,塑料牌号太多,本网站没有提供的本公司也有代理,详情请咨询本公司相关业务人员0769-87795123
 
13549213581
Technical Data
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Features and Benefits
 
•Wide service temperature
 
–200° to +150°C
 
•Low flammability
 
•Excellent electrical and
 
mechanical properties
 
•Low permeability
 
•Good resistance to radiation
 
•High light transmission in the
 
visible and UV ranges
 
•Very good resistance to solvents
 
and chemicals
 
•Extremely high resistance to
 
outdoor weathering
 
•Non - stick characteristics
 
 
 
 
 
3M™ Dyneon™
Fluoroplastic Granules
ET 6235Z
 
Typical Properties
 
Property Test Method
Melt Flow Index (297°C/5 kg) ASTM D1238 10 g/10 min
Specific Gravity ASTM D792 1.73 g/cm3
Tensile Strength 23°C ASTM D638 46 MPa (6,670 psi)
Elongation @ Break 23°C ASTM D638 425%
Yield Stress 23°C ASTM D638 25 MPa (3,360 psi)
Flexural Modulus ASTM D790 1,100 MPa (159,500 psi)
Light Transmission 95%
(visible range as a function of film thickness)
Dielectric Constant ASTM D150 2.58 @ 1 MHz
Dielectric Strength, 0.1 mm ASTM D149 150 kV/mm
Melting Point ASTM D4591 267°C (513°F)
Maximum Service Temperature DIN 57207 part 6 150°C (302°F)
Limiting Oxygen Index (LOI) ASTM D2863 >30
Vertical Burn1 (110 mm thick) UL 94 V-0 low flammability
1 measured on compression molded plaques, 2 mm thickness
 
 
•Excellent tear resistance
 
•Nonflammable
 
 
Note: Data in this document are not for specification purposes.
 
 
Product Description
 
3M™ Dyneon™ Fluoroplastic Granules ET 6235Z is a melt processable fluoroplastic consisting mainly of alternating tetrafluoroethylene and ethylene monomer units (ETFE). This partially crystalline fluorothermoplastic offers a valuable combination of properties.
 
Applications
 
Its excellent properties make Dyneon ET 6235Z ideal for use in a wide variety of industries, including applications in the electronics, chemical processing, laboratory testing equipment and outdoor architectural structure industries. It can be easily fabricated into films, extruded thin-walled tubing and injection molded parts.
 
Processing
 
ET 6235Z can be processed by the methods normally employed for thermoplastics, such as injection molding, extrusion and blow molding. It is recommended that any machine parts that come in contact with the melt should be constructed with a corrosion-resistant finish, such as XaloyTM, HastelloyTM or similar material. Processing temperature range, 320°C (610°F)- 340°C (645°F).
 
 
Storage and Material Handling
 
ET 6235Z has an unlimited shelf life provided it is stored in a clean, dry place. ET 6235Z is hydrophobic, and generally does not require drying before processing unless high humidity conditions create surface moisture adsorption.
 
Safety/Toxicology
 
This is a fluoroplastic material, so normal precautions observed with fluoroplastics should be followed. Before processing this product, be sure to read and follow all precautions and directions for use contained in the product label and the Material Safety Data Sheet. General handling/processing precautions include: (1) Process only in well-ventilated areas; (2) Do not smoke in areas contaminated with powder/residue from this product;
 
(3) Avoid eye contact; (4) After handling this product, wash any contacted skin with soap and water. Potential hazards, including evolution of vapors, can exist if processing occurs under excessively high temperature conditions. Vapor extractor units should be installed above processing equipment. When cleaning processing equipment, do not burn off any of this product with an open flame or in a furnace.
3
 
 
 
 
 
东莞市双帮塑胶原料有限公司大量销售塑料美国3M ETFE 3M™ Dyneon™
Fluoroplastic Granules
ET 6235Z
因为塑料价格行情每天都有新的变化前天的报价不等于今天的报价。如果需要新的价格请电:13549213581,肖生。